Saitreg Fuel Nozzles Fuel Nozzles and Pumps

Inline Fuel Filter Marine

Inline Fuel Filter Marine

I purchased a boat and also bought a 1970 85 hp outboard evinrude motor from a different place. The motor has been working fine but when we bought it he said he usually replaces the impeller every year and had not gotten around to it yet this year. My husband and I have never owned a boat before and are just starting to learn all the fun things and decided to wait to do the impeller until we actually used the boat motor and knew it worked good and everything.

Well we took it out the other night and the motor acted like it was missing and kind of revving up a bit. We changed the spark plugs and then took it back out. We think that actually sounds better now but while my husband was at the back watching the motor he noticed that no water was coming out of the holes. We have ordered a new impeller.

Any marine dealer can get you those parts. Check the wear plate and cup for any grooves near the driveshaft, if so replace the parts, if not just the impeller. You may not have water coming out of the exhaust relief. Your best bet would be to take it to a good service shop and have them go over the motor, install a tell tale or water pressure gage. Have them do a complete check of the motor. Since you guys are new to boating and the motor is almost 40 years old it is best to have an expert tell you what you have. While some things are possible for a DIYer with some good tools, many things aren't.

I have a 1990 Bay liner Cobra with a 1986 115 Mariner inline 6. I have had the boat for about a month now, and have honestly not had a day where I didn't have a problem. So far I have had the carbs rebuilt, the fuel filter pump rebuilt, the impeller replaced took it out ran fine for about an hour then stalled out and had to get towed back in.

Took it home called around and was told that my problem was the power pack because 1,3,5 was firing but others wasn't and when I swapped the two power packs the 2,4,6 started working. Well I bought a used one at the boat yard and got the spark back. Took it on the lake today and ran GREAT for about a quarter of a mile.

Then started cutting out and made the motor started jerking and wouldn't go over like 3000 RPMs (sometimes speeding up like it wanted to take off but would then start restricting itself again), but would run fine if I kept it under 2000 or 1500 RPMs shuddering at times. Made it back to the dock where we pulled the caps to the plugs off one at a time checking for spark. The plugs would spark fine fewer than 2000 RPMs, but would start missing on all of them if we got it over 2000. I have spent more time fixing this stupid thing than I have actually using it.

That motor is one of the best ever made. Essentially it is the same as the 150 of 1978 with updated ignition. First of all I would never recommend buying used ignition parts, you don't know how long they will last, have no warranty and may be on their last legs. Most of the switchbox's have updated components. I only recommend either Mercury's or CDI. As for your problem it would appear you have a bad stator. Mercury has put out numerous service bulletins on it.

What is happening is you have two sets of charge coils and one set of alternator coils on your stator.

The stator is the series of coils under your flywheel. One set is the low speed, and the other the high speed. In your case the high speed coils have gone out. You will need to replace the entire stator. Here again I recommend you find a stator by CDI Electronics, have your local shop order you one. They have beefed up the coils and added another regulator. You will need special tools to remove the flywheel. Don't try to play with a normal wheel or pulley puller, you will damage the flywheel and will just have to go out and buy another one.

Victor Epand is an expert consultant at http://www.SellUsedBoatParts.com/. Sell Used Boat Parts is a community of various independent used boat parts sellers from around the world. Each used boat parts seller represents a unique style of products all their own. If you have used boat parts to sell, click here to create a Boat Parts Account.

Billet Inline Fuel Filter $9.91 Billet aluminum inline fuel filter for 2-stroke pocket bikes and vehicles. 30mm In Length Takes size 5 mm fuel line Unscrews for easy cleaning

Inline Fuel Pressure Regulator $154.99 Inline Fuel Pressure Regulator; Up To 300 gal. Per Hour; 3-12 psi Range;

Y Inline Mini Filter ¾'': A $17 This is an inline filter with ¾'' male threads used in Botanicare Botanicare modular systems.

Culligan IC101 Inline Water Filter $29.9 The Culligan IC101 is the replacement inline refrigerator water filter for the inline filter Culligan IC102 Inline Filter. The Culligan IC101 inline water filter reduces chlorine taste and odor.

Inline Gas/Oil Filter by K&N $106.99 Inline Gas/Oil Filter; Race Only; -10AN; 25 Micron; Stainless Steel; Anodized Aluminum Housing; Inline Gas/Oil Filter by K&N

Inline Fuel Cooler $60.99 Provides Colder Fuel To Engine,Higher Potential Fuel Energy,Supplied With Gator Clips,With #6AN Fittings Standard,Made in USA

Dickinson Marine 20010 Fuel Filter and Brass Manual Shut Off $135.32 This stainless and glass filter features a manual shut off valve. Glass see thru bowl easy to clean; chrome finish. Stone filter element included. With shutoff valve. For Dickinson heaters and stoves.

Power-Plus Series; Inline Fuel Pump System $299.99 Power-Plus Series; Inline Fuel Pump System; Over 50 GPH; Incl. All Hardware; Turbo/Supercharger/Nitrous;

Y Inline Mini Filter 1'' #60500: A $17 This is an inline filter with 1'' male threads used in Botanicare Botanicare modular systems.

Trans-Dapt Fuel Filter Element $4.99 Fuel Filter Element

Inline Gas/Oil Filter Element by K&N $70.99 Inline Gas/Oil Filter Element; Race Only; Replacement; 25 Micron; For Use w/PN[81-1002/81-1004/81/1005]; Inline Gas/Oil Filter Element by K&N

Jeep In-Tank Fuel Filter by Omix-Ada 17728.02 $11.99 1987 to 1990 Jeep YJ Wrangler with 4.2L engine;1972 to 1986 CJ with 3.8L and 4.2L engines;1972 to 1990 Cherokee and SJ Grand Wagoneer with 4.2L engines;Inline with dual outlets JEEP CJ5 CJ7 SCRAMBLER 1982 1983 1984 1985 1986 2.5L (150) 2.5L Iron Duke LX8 (151) 4.2L (258) GAS Jeep In-Tank Fuel Filter by Omix-Ada 17728.02

Culligan IC102 Inline Water Filter $39.15 Culligan IC102 refrigerator water filters produce cleaner bettertasting ice cubes and beverages. The Culligan IC102 inline filter reduces chlorine taste and odor sediment bad taste and odor. Greattasting and healthier drinking water and ice cubes. Works great as an inline filter for water dispensers and ice makers.

Fuel Filter $40.99 Fuel Filter; High Pressure; Stainless Steel; 2 pc. Laser Welded Construction;

Aquasana Inline Water Filter $68.58 The Aquasana Inline Water Filter produces naturally healthy water for drinking, cooking, ice and beverages. This water filter is great for water fountains, ice makers, RVs or under-sink refrigerator supply line.Aquasana Inline Water FilterModel: AQ-7000Filter lasts 300 gallons/ 6 monthsFilters out chlorine, lead, VOCs, THMs, cysts, turbidity and most other tap water contaminants Uses compressed carbon, ion exchange and sub micron filtrationFor any application that requires constant pressure and a flow rate of 0.375 gallons per minute1/4-inch Quick Connect FittingsNo tools or power needed, installs in minutesDimensions: 12 inches long x 3 inches in diameterAssembly Required

Pentek IC101L Inline Water Filter $28.59 The Pentek IC101L is the replacement inline water filter for the Culligan IC102 inline filter and the Culligan IC101 inline filter. The fittings are not included with the Pentek IC101L inline water filter. Unscrew the fittings from your old filter and screw them into the new filter. The fittings should be for 1/4 NPT connections. The Pentek IC101L sealed inline filters feature coconut shell granular activated carbon and are designed to reduce unwanted taste odor and chlorine taste and odor. The Pentek IC101L inline filters produce greattasting and healthier drinking water and ice cubes. Works great as an inline filter for water dispensers and ice makers. Injection molded and pressure rated to 125 psi. The Pentek IC101L includes a prefilter and postfilter. The Pentek IC101L sealed inline filters are an ideal choice for postRO undersink icemaker and food service applications. The ICMB inline mounting bracket for the Pentek IC101 can be purchased below. To inhibit lime and scale buildup consider purchasing the Pentek TS101L inline water filter. Connections: 1/4 NPT. Filter Life: 2 500 Gallons (9 460 liters). Flow Rate: 0.75 gpm (2.8 L/min). Dimensions: 2 W x 101/2 L (51 mm x 270 mm). Media: Coconut Shell GAC 17 cu. in. Body Cap Prefilter and Postfilter: Polypropylene. Carbon: Coconut Shell GAC. Operating Pressure: 125 psi (8.62 bar). Maximum Temperature: 100deg;F (37.8deg;C).

Liquatec CLP20W 2 in. Inline Filter Clip $18.21 The CLP20W clip is a single inline mounting bracket for inline water filters. The CLP20W Inline Filter Clip can be used with most 2 Wide inline water filters. The CLP20W clips on to inline water filters for mounting on a wall or other flat surface. The screw is not included with the inline filter clip. All 2.0 Wide inline water filters. The 2.0 Diameter clip fits on any brand.

Inline Tube JPB102 - 3/8 Fuel Line Clip Set by Inline Tube - JPB102 $13.99 1976-86 CJ7 and CJ5;Galvanized;8-piece set Inline Tube JPB102 - 3/8" Fuel Line Clip Set by Inline Tube - JPB102

AEM Fuel Filter - Blue [94-01 Acura Integra] $125.35 AEM Fuel Filter - Blue

AEM Fuel Filter - Blue [95-00 Honda Civic] $125.35 AEM Fuel Filter - Blue

AEM Fuel Filter - Blue [97-01 Honda Prelude] $125.35 AEM Fuel Filter - Blue

AEM Fuel Filter - Silver [94-01 Acura Integra] $125.35 AEM Fuel Filter - Silver